Print Version (PDF) [ close ]   

 SiberProp Product Photo

Technical Data Sheet

 

 

 

 

 

SiberProp

Low Temperature Resin Coated Sand with Stress Bond™ Technology

 

DESCRIPTION

SiberProp™ proppants are a Stress Bond™ technology resin coated sand available in a 16/30 and 20/40 mesh sizes. Tan in color, the SiberProp resin system is applied to high quality frac sand. The unique properties of the SiberProp resin have redefined curable proppants. By using a specially formulated resin system, SiberProp proppants develop significant strength in the bonded pack at very low bottom-hole temperatures without the need for external consolidation aids.

 

TYPICAL APPLICATIONS

Fracture treatments:  

  • At closure stress up to 55MPa [8,000 psi]
  • At bottom-hole static temperatures from 54 – 93°C [130 – 200°F]
  • When high strength in the bonded pack is necessary or desirable at very low temperatures
TECHNICAL ADVANTAGES 
  • Low temperature bonding down to 54°C [130°F] bottom-hole static temperature without the use of a consolidation aid
  • Optimized AcTivator™ consolidation aid loading recommendations are available based on well specifics to maximize performance and minimize additional cost to the operator
  • Higher strength in the bonded pack at lower temperatures than conventional curable resin coated proppants
  • Consolidates with closure stress in the fracture 
  • Helps prevent proppant flowback 

TECHNICAL CONSIDERATIONS

  • Grain-to-grain contact must occur and closure stress must be applied during the cure period for proper bonding
  • Consolidation of curable product at bottom-hole static temperatures below 54°C [130°F] is achieved by the use of our AcTivator low temperature consolidation aid

 

 Chemical Properties

 Typical

Composition

resin coated frac sand

Resin type

thermosetting, curable

Color

tan

Solubility, weight %

 

in water, brine & HCl

nil

in HCl/HF acid, API RP 19C

≤ 0.3

in oil

nil

Compatibility

Fully compatible with most commonly used fracturing fluids, both water and oil-based systems. Testing with fluids prior to pumping is advised.

 

 Physical Properties

 Typical

API Mesh Size

16/30, 20/40

Physical State

solid granule

Specific Gravity

2.55, 21.5

Bulk Density  
g/cm3 [lb/gal] 1.54 [12.9], 1.56 [13.0]

Pipe Fill Factor

 

cm3/g [gal/lb]

0.649 [0.0775], 0.641 [0.0768]

Absolute Volume

 

cm3/g [gal/lb]

0.392 [0.0470], 0.389 [0.0465]

Median Particle Diameter (mm) 0.9097, 0.6390

Particle Size Distribution 

meets or exceeds API RP 19C

Turbidity, NTU (FTU)

≤ 250

11/09

 

 

SiberProp Canada Chart   

 

  

 Contact Information

Hexion

Oilfield Technology Group

633 - 6th Ave. SW, Suite 400

Calgary, AB Canada  T2P 2Y5

+1 403 705 0950

 www.hexion.com/oilfield

Customer Service 

+1 800 626 2116

 otg.customerservice@hexion.com

Technical Inquiries

 otg.customerservice@hexion.com

 

® and ™ Licensed trademarks of Hexion Inc.

DISCLAIMER

The information provided herein was believed by Hexion Inc. (“Hexion”) to be accurate at the time of preparation or prepared from sources believed to be reliable, but it is the responsibility of the user to investigate and understand other pertinent sources of information, to comply with all laws and procedures applicable to the safe handling and use of the product and to determine the suitability of the product for its intended use. All products supplied by Hexion are subject to Hexion’s terms and conditions of sale. HEXION MAKES NO WARRANTY, EXPRESS OR IMPLIED, CONCERNING THE PRODUCT OR THE MERCHANTABILITY OR FITNESS THEREOF FOR ANY PURPOSE OR CONCERNING THE ACCURACY OF ANY INFORMATION PROVIDED BY HEXION, except that the product shall conform to Hexion’s specifications. Nothing contained herein constitutes an offer for the sale of any product.

Print Version (PDF) [ close ]